Professional Manufacturer for Siway SV-602 Epoxy Structural Adhesive A/B to Holland Manufacturers
Short Description:
Description SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion. Key Features 1. Room temperature curing Epoxy adhesive 2. Fast cure at room temperature,...
Our primary goal is to offer our clients a serious and responsible business relationship, providing personalized attention to all of them for Professional Manufacturer for Siway SV-602 Epoxy Structural Adhesive A/B to Holland Manufacturers, We sincerely welcome you come to visit us. Hope we have good cooperation in the future.
Description
SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.
Key Features
1. Room temperature curing Epoxy adhesive
2. Fast cure at room temperature, <40 min for reaching a tack-free status under standard environment (STD: 23℃, 50% humidity)
3. Mix ratio of 1:1 by volume or by weight
4. Good mechanical property
5. Bonds a wide variety of building materials
6. Good waterproofing and chemical resistance
Basic Application
1, the external walls of stone material, ceramic and other hang bond;
2, concrete, ceramics, stone, wood and other prefabricated split, bonding and jointing;
3, concrete, stone and so on crack repair;
4, the structure of the localization, anchor, reinforcement and reinforcement.
Technical data sheet
The following data is for reference only and is not recommended for the specification
| Shear strength | Stainless steel-stainless steel/Standard conditions | ≥18 | JC887-2001 | ||
| Pressure shear strength | Stone-stone/ Standard conditions | ≥12 | |||
| Stone-stone/ The freeze-thaw cycle 50 times | ≥10 | ||||
| Stone – stainless steel/ Standard conditions | ≥12 | ||||
| Standard conditions：Temperature=23℃，relative humidity=50%，48 hours curing | |||||
| attribute | SV-602-A | SV-602-B | SV-602(After mixing) | ||
| Colour | gray | white | grey | ||
| Density(g/cm³) | 1.8 | 1.8 | 1.8 | ||
| Viscosity（PaS） | 200-400 | 150-250 | |||
| Effective operating time(23℃) | N/A | N/A | 20min | ||
Certification
JC 887-2001
Color
Part A-Grey Paste/Part B-White Paste
Package
9kg/9kg per unit and 15kg/15kg per unit
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
Terry talks about Tyvek which is a rain shield that protects the house from moisture. When water goes through a homes siding, it hypothetically hits this barrier and runs down to the ground. Terry further notes that the rain shield does not provide air sealing; instead, all the air sealing is already taking place behind the Tyvek in the polyisocyanurate foam, OSB, and behind the OSB where the spray foam has been applied.
Furring strips are put over the Tyvek, so that when siding is placed over it, there is an air space between the siding and rain shield. In other words, air can circulate beneath the siding to dry it out if it gets too wet thus avoiding a possibility of deterioration. The window trim is then put up on top of the furring strips. A bug screen is then applied on top and bottom of the furring strips and Tyvek. The siding, fiber cement Hardie board, is finally put on. The practice of putting on furring strips on top of the rain shield is different from traditional building where this step is skipped; instead, the siding is put right on top of the rain shield.
This mold making tutorial video shows how to make a support shell for a brush on silicone mold using Plasti-Paste trowelable plastic. The finished mold can be used for casting resin, wax, foam, and many other materials.
Make It Now! with Smooth-On
https://www.smooth-on.com/
https://www.facebook.com/SmoothOn
https://twitter.com/SmoothOn
https://www.google.com/+smoothon
