High Performance Siway SV-602 Epoxy Structural Adhesive A/B for Kuala Lumpur Factory
Short Description:
Description SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion. Key Features 1. Room temperature curing Epoxy adhesive 2. Fast cure at room temperature,...
We always stick to the principle "Quality First, Prestige Supreme". We are fully committed to providing our clients with competitively priced quality products, prompt delivery and professional service for High Performance Siway SV-602 Epoxy Structural Adhesive A/B for Kuala Lumpur Factory, welcomes all overseas friends and merchants to establish collaboration with us. We will provide you with honest, high quality and efficient service to meet your requirements.
Description
SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.
Key Features
1. Room temperature curing Epoxy adhesive
2. Fast cure at room temperature, <40 min for reaching a tack-free status under standard environment (STD: 23℃, 50% humidity)
3. Mix ratio of 1:1 by volume or by weight
4. Good mechanical property
5. Bonds a wide variety of building materials
6. Good waterproofing and chemical resistance
Basic Application
1, the external walls of stone material, ceramic and other hang bond;
2, concrete, ceramics, stone, wood and other prefabricated split, bonding and jointing;
3, concrete, stone and so on crack repair;
4, the structure of the localization, anchor, reinforcement and reinforcement.
Technical data sheet
The following data is for reference only and is not recommended for the specification
| Shear strength | Stainless steel-stainless steel/Standard conditions | ≥18 | JC887-2001 | ||
| Pressure shear strength | Stone-stone/ Standard conditions | ≥12 | |||
| Stone-stone/ The freeze-thaw cycle 50 times | ≥10 | ||||
| Stone – stainless steel/ Standard conditions | ≥12 | ||||
| Standard conditions：Temperature=23℃，relative humidity=50%，48 hours curing | |||||
| attribute | SV-602-A | SV-602-B | SV-602(After mixing) | ||
| Colour | gray | white | grey | ||
| Density(g/cm³) | 1.8 | 1.8 | 1.8 | ||
| Viscosity（PaS） | 200-400 | 150-250 | |||
| Effective operating time(23℃) | N/A | N/A | 20min | ||
Certification
JC 887-2001
Color
Part A-Grey Paste/Part B-White Paste
Package
9kg/9kg per unit and 15kg/15kg per unit
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
GAF- Mastering The Roof (chapter 14)
The Liberty™ System is designed for both new roofing and re-roofing applications.
Full Installation Guide for Low Slope Modified Roofing (Cold-Applied Liberty System).
Low Slope Roofing Systems such as Liberty should only be installed on roof slopes of 2 in 12″ or higher. Never install it on roofs with ponding water.
This guide covers following procedures:
Deck Preparation
Base Ply Install
Middle Ply Install
Cap Sheet Installation
Drip Edge, Flashing and Accessory Installation details.
Low slope areas such as the roofs of carports, garages, porches and sun rooms – anything below a 2/12 pitch requires special attention.
Without the drainage of a steep slope, these roofs can take a hard beating from rain, ice and snow.
You’ve probably seen the problem leaks that occur where these low slope roofs tie in with the main house.
To provide you with materials that can meet these challenges, GAF has developed a series of self adhering membranes that go down easy, apply with simple tools and provide maximum protection. Lets take a look at these revolutionary low slope products and see how they install.
Liberty is a system for low slopes with a pitch between 1/2” to 6” per foot. Designed as a Whether installing Liberty Mechanically Attached Base Sheet, or Liberty Self Adhered Base Sheet, your edge metal details are the same.
At the edge of the roof, install drip edges. Primed Metal drip edge is required at eaves and rakes on Liberty Systems. At eaves and rakes, install a bed of Topcoat® Matrix 201 Premium SBS Flashing Cement to set the metal drip edge into. Next, to better seal the flange to the Base Sheet Base/Ply, nail the drip edge 3” on centers in a staggered pattern using roofing nails. Finally, apply a 1/16 to 1/8 inch troweling of Matrix 201 Premium SBS Flashing Cement to the top of the metal prior to installing the Liberty Cap Sheet over drip edges. Using a notched trowel helps assure a proper application rate of adhesive.
Working from the center of the length of Base Ply Sheet, allow the sheet to roll onto the primed deck, being careful to avoid wrinkles and trapped air while maintaining proper alignment with the selvage edge of the previous course.
Firmly hand press the sheet to avoid wrinkles and trapped air as the Base/Ply adheres to the underlying base sheet or primed deck.
Now fold the other half of the sheet back on itself exposing the remaining release film. Remove the release film and roll the sheet in place working from the center of the sheet outward towards the ends of the sheet.
Flashing of walls, roof terminations and penetrations can also be done with Liberty membranes and pre-flashed, SBS M-Weld Units.
As with all vertical flashings, the flashing is nailed off at the top and counter flashed.
Talent On Camera
Liberty is just one of the self-adhered products offered by GAF. Others include the Freedom series of self-adhered TPO roofing membranes.
Freedom membrane is a tough commercial grade membrane that is easy to install, long lasting and energy efficient with a white reflective surface. For further information on self adhered roofing technology, visit GAF.com or call 1-800-ROOF-411. That’s 1-800-766-3411.
https://www.energyimprovements.net 800-256-5867 Resealing the air handler, plenum and ducts can be a huge energy savings. It is not uncommon to lose 10% of your air or heat into the attic before it reaches the intended vents and inside rooms of our homes. There are a couple ways to reseal these area’s, one would be to use a hvac commercial grade aluminum foil tape. This method is OK, but no matter the quality of the tape its a matter of time before it peels or cracks and therefore ending up with the same problem. The best way to reseal these ducts and plenum is with a mastic. The mastic is what a good hvac company will use. It goes on like a plaster and creates a hard seal. This seal is permanent and will last as long as the unit will. Energy Improvements installers inspect and repair ducts, plenum and air handlers when installing there Energy Improvement Shield Radiant Barrier. This is going the extra mile and giving the radiant barrier and energy savings a real boost.
