Factory source manufacturing SV-312 Polyurethane Sealant for Windshield Glazing for Malaysia Manufacturer

We believe that long term partnership is a result of high quality, value added service, rich experience and personal contact for Factory source manufacturing SV-312 Polyurethane Sealant for Windshield Glazing for Malaysia Manufacturer, If you are interested in any of our products and services, please don't hesitate to contact us. We are ready to reply you within 24 hours after receipt of your request and to create mutual un-limited benefits and business in near future.

Description

SV-312  is an isocyanate-free, high modulus,non conductive, thixotropic, single component modified polyurethane adhesive, which polymerizes rapidly under the effect of atmospheric moisture. It has been specially designed for bonding of fixed glass in automotive repair.

It allows a drive away time of 6 hours in vehicles with or without airbag.

*Providing the ambient temperature is at least 23°C and relative humidity 50 %.

At lower temperatures and humidities drive away time will be longer.

Where to use

Bonding and sealing for windshield glass, glass fiber reinforced plastic fittings, steel and aluminum board of automobiles.

Key Features

a. Fast curing under room temperature, no sagging, solvent free

b. High bonding strength, 

c. Good chemical and water resistance

d. No conductive

e. Excellent noise, vibration and impaction resistance

f. Automotive OEM quality

Technical data sheet

Color

White, black, grey

Package

300ml plastic cartridges and 600ml in sausage

Shelf life

9 months 

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

Glass tile Mosaic Bathroom with many decorative elements including inserts borders and diagonal marble floor

Paper faced mosaic glass tile requires an installation method that has a few more steps that would normally be used compared to other types of mosaic tile. This is especially true if the mosaic glass tile is transparent. First it is important to use the correct setting material to install glass tile. Glass tile should never be installed using mastic. The type of thinset needed to install glass tile is one that is white and has a high polymer content. I usually use “Tec Superflex”. It is also important that the thinset used is one that has the same color across multiple units, to insure color consistency when installing large projects that require more than one bag of thinset. Using a lower quality thinset can cause variation in color and shading of the glass tile, and also result in tiles not adhering to the mortar. Paper faced tiles like the Oceanside mosaic tile used in this video are usually very thin so oozing of the thinset between the tiles can be a problem if the correct trowel is not used to spread the thinset. Despite this one hundred percent coverage must be achieved on the back of the tile to obtain a proper installation. If 100% coverage is not achieved, visible color shading will be present throughout the tile installation which will create an unpleasant final product. In this case I used a 3/16″th V-Notched trowel. The thinset is first spread on the wall with the notched side of the trowel in such a way that the lines left by the trowel are all even in depth and uniformly going in the same direction. Once this is achieved, the flat side of the trowel is used to “Knock” down the ridges and create a flat even bed of mortar, but at the same time not removing any of the thinset from the wall. The next step is to start setting the tiles in the prepared thinset by placing the tiles on the wall a sheet at a time, aligning the grout lines between sheets. Once a number of sheets have been placed then it is time to “Beat them in” this is done by placing a flat piece of wood, such as a small segment of 2×4, on the tile and then gently tapping the wood with a hammer so as to set the mosaic tile into the thinset until 100% coverage is achieved. Do not use a rubber float to beat in the tile. Let the tile “Set” for a period of time, 30 minutes more or less. Once this time period has elapsed it is time to start wetting the paper for removal. This will probably take 5 to 10 minutes and require that you wet the surface of the paper several times. When the paper has loosened start pealing it off the tile, do not wait until the next day to do this, remove the paper while the thinset is still fresh. This will allow for necessary adjustments to individual tiles. Continue this process until the installation of the tile is complete. Allow the tile to set, all residue of the paper adhesive should be removed before grouting. Determine whether sanded or unsanded grout should be used, in this case sanded grout was needed. Some glass mosaic tile require that they be sealed before grouting, this particular tile did not call for sealing. The proceeding is intended as a guide line and not complete instructions on how to install mosaic glass tile, complete installation instructions are usually supplied with the tile at the time of purchase, or may be included in the tile packaging.
This Oceanside mosaic glass tile bathroom was installed by Sal DiBlasi, Elite-Tile Company in Boston’s North Shore.
Youtube Channel https://www.youtube.com/user/saldibs?feature=watch
Facebook https://www.facebook.com/pages/Elite-Tile-Company/56681633342
Website https://www.elitetileco.com/