factory low price SV-777 silicone sealant for stone for Muscat Importers
Short Description:
Description SV-777 silicone sealant for stone, is an elastomer sealant in modulus, single. Waterproof joints need to be sensitive to natural stone, glass and metal building clean appearance panel for sealing design, it to the moisture in the air after curing in contact, the formation of elastic rubber sealing performance, durability, weather resistance, good combination with most building materials. Key Features 1. 100% silicone 2. Minimized fluid migration 3. Low dirt pick up 4. Water &...
With our rich experience and considerate services, we have been recognized as a reliable supplier for many international buyers for factory low price SV-777 silicone sealant for stone for Muscat Importers, Welcome friends from all over the world come to visit, guide and negotiate.
Description
SV-777 silicone sealant for stone, is an elastomer sealant in modulus, single. Waterproof joints need to be sensitive to natural stone, glass and metal building clean appearance panel for sealing design, it to the moisture in the air after curing in contact, the formation of elastic rubber sealing performance, durability, weather resistance, good combination with most building materials.
Key Features
1. 100% silicone
2. Minimized fluid migration
3. Low dirt pick up
4. Water & weatherproof
5. Primerless adhesion to most building materials
6. 25% movement capability
Basic Application
1.Stone curtain wall sealing
2.Engineering ceramic sealing
3.Stone and other materials such as glass, metal seam sealing
4.Other uses
Technical data sheet
| Test standard | Test project | Unit | value |
| Before curing——25℃，50%R.H. | |||
| ASTM C 679 | Flow, sagging or vertical flow | mm | 0 |
| VOC | g/L | ＜80 | |
| GB13477 | surface drying time（25℃，50%R.H.） | min | 30 |
| Curing time（25℃，50%R.H.） | Day | 7-14 | |
| Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.21 days after curing——25℃，50%R.H. | |||
| GB13477 | Durometer Hardness | Shore A | 30 |
| GB13477 | The ultimate tensile strength | Mpa | 0.7 |
| Temperature stability | ℃ | -50~+150 | |
| GB13477 | Movement capability | % | 25 |
| ASTM C 1248 | Pollution / oil, natural stone | No | |
Certification
25HM GB/T 23261-2009；ASTM C920-2011
Color
Black，White，Gray
Package
300ml in cartridge * 24 per box, 590ml in sausage *20 per box
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
Tired of boring drink coasters? Let’s design our own with just a few simple supplies. You will need a picture, some tiles, mod podge, felt and a brush!
Email List Signup: https://householdhacker.tv/list
Full Instructions:
To pull this off we need a few basic items… a cutting board or scissors… Some mod lodge glue and sealant. a brush, some ceramic tiles and some felt.
If you want a custom design print out a couple color pictures but leave enough room for about 4 and a half inches each. A standard piece of paper can hold a couple of these.
We are using a standard 4×4 ceramic tile. These can be purchased at the hardware store for about 18 cents each!
Print out your design and lets cut it up! You want to make a square that is 4 and 1/8th inches on all sides.
Once you cut it up place it on the tile to make sure the measurements were correct. You want a little bit of white as a border.
Now grab some mod lodge and apply a thin coat directly on to the tile. In a pinch you could use elmers glue but the top layer will not be as clean and good looking.
At this point it’s good to mention that you don’t have to print anything, you can cut logos or pictures out of a magazine or old book to make your awesome coasters however you want… just follow the same process as before.
Once the image is centered and secured into place. Apply a first top coat to the picture. Go slowly and steady here to avoid bubbles in the paper. Make a nice thin and straight layer and then give it at least 10 minutes to dry.
After you have applied about 3 layers, you should have a nice water proof and flush looking coaster. It’s time to pad the bottom with felt to finish up the project.
Get your felt out which can be purchased at any art store and cut it to the same size at the paper… That’s 4 1/8 inches on all sides. Now apply another thin layer of mod lodge or glue to the bottom and carefully place the felt into position.
And that’s it! Once this process is completed, let everything dry for about an hour and they are ready for use! These things make great gifts for anyone.
-~-~~-~~~-~~-~-
NEWEST VIDEO: 10 Ways To Reuse Soda Cans In Your Home
-~-~~-~~~-~~-~-
Scotty Kilmer, mechanic for the last 46 years, shows how you can fix a leaking axle seal that’s throwing oil on the inside of your tires. Why pay a mechanic hundreds when you can do it yourself with a little elbow grease. And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&feature=c4-overview . And remember, every TUESDAY I upload a new video, so don’t miss them.
