Discount wholesale SV-8000 PU Sealant for Insulating Glass Wholesale to Qatar
Short Description:
Description SV – 8000 two-component polyurethane insulating glass sealant is a neutral cure, mainly used for the insulating glass of the second seal. Product formulation to use its performance with high modulus, high strength, to meet the requirements of insulating glass assembly. Where to use It is a two-component PU sealant that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU. Key Fe...
We are proud of the high customer satisfaction and wide acceptance due to our persistent pursuit of high quality both on product and service for Discount wholesale SV-8000 PU Sealant for Insulating Glass Wholesale to Qatar, We are confident that there will be a promising future and we hope we can have long term cooperation with customers from all over the world.
Description
SV – 8000 two-component polyurethane insulating glass sealant is a neutral cure, mainly used for the insulating glass of the second seal. Product formulation to use its performance with high modulus, high strength, to meet the requirements of insulating glass assembly.
Where to use
It is a two-component PU sealant that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.
Key Features
1. High Modulus
2. UV resistance
3. Low vapor and gas transmission
4. Primerless adhesion to coated glass
Technical data sheet
| Test project | standards | Value |
| Sagging degree (mm) | ≤3 | 0 |
| Operating time | ≥30 | 30 |
| Thermal weight loss(%) | ≤10 | 2 |
| Durometer Hardness Shore A | 20-80 | 42 |
| tensile propcrties（MPA） | ＞0.4 | 1.0 |
| Bond damage area（5%） | ≤5 | 0 |
Certification
GB-24266-2009;
Color
Component A(Base) – White, Component B(Catalyst)- Black
Package
1. Component A(Base): (190L), Component B(Catalyst) (18.5L)
2. Component A(Base):24.5kg (18L), Component B(Catalyst): 1.9kg (1.8L)
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
Jeep Liberty Water Pump Replace. This is a 2003 Jeep Liberty Sport with a 3.7 engine , that has a bad water pump.The serpentine belt was already taken off the jeep liberty so we could load the jeep up on the trailer. You will need to drain the rest of the jeeps antifreeze out and you can either take the bottom radiator hose off to drain . There may be a drain plug in the jeep liberty radiator but i did not look, the hose was right there.To get the water pump off the jeep liberty you will need to remove the idler pulley.. Then the water pump can be removed from the jeep liberty ,by removing the bolts from the water pump. the 3.7 jeep liberty water pump is not to hard to do compared to many other vehicles. Clean the surface that the water pump will seal on the 3.7 block. Then just reverse the steps to reinstall the water pump on the 3.7 jeep liberty.
Due to G+ Allowing links to be posted and I do not have time to make sure all links are safe ,ANY post with a link in it will be deleted. Sorry. .
car repair
Save yourself future hassles of car starting issues by using Battery Protectors. It prevents acid corrosion on the battery post and terminals (which causes bad electrical connection). You can find Battery Protectors at Amazon (affiliate link): https://amzn.to/2sLrVqp
This product is low cost and definitely worth it. Battery Terminal Protectors pads. NCP2 Noco corrosion preventive. I use this on all my cars to prevent starting problems because the terminals became corroded from battery acid fumes leak. Ultra premium oil based proven formula pad. These pads will last the lifetime of car battery life. This product is a must use. It works great! Easy to install and cost is very cheap.
Directions:
1. Clean battery terminals before installation.
2. Remove battery cables: negative (-) cable first.
3. Place terminal protector between battery cable and terminal post. (remove inner ring for side terminals.)
4. Reconnect battery cables: positive (+) cable first.
