China Cheap price SV-777 silicone sealant for stone for Malaysia Factory
Short Description:
Description SV-777 silicone sealant for stone, is an elastomer sealant in modulus, single. Waterproof joints need to be sensitive to natural stone, glass and metal building clean appearance panel for sealing design, it to the moisture in the air after curing in contact, the formation of elastic rubber sealing performance, durability, weather resistance, good combination with most building materials. Key Features 1. 100% silicone 2. Minimized fluid migration 3. Low dirt pick up 4. Water &...
We have a highly efficient team to deal with inquiries from customers. Our goal is "100% customer satisfaction by our product quality, price & our team service" and enjoy a good reputation among clients. With many factories, we can provide a wide range of China Cheap price SV-777 silicone sealant for stone for Malaysia Factory, We are confident that there will be a promising future and we hope we can have long term cooperation with customers from all over the world.
Description
SV-777 silicone sealant for stone, is an elastomer sealant in modulus, single. Waterproof joints need to be sensitive to natural stone, glass and metal building clean appearance panel for sealing design, it to the moisture in the air after curing in contact, the formation of elastic rubber sealing performance, durability, weather resistance, good combination with most building materials.
Key Features
1. 100% silicone
2. Minimized fluid migration
3. Low dirt pick up
4. Water & weatherproof
5. Primerless adhesion to most building materials
6. 25% movement capability
Basic Application
1.Stone curtain wall sealing
2.Engineering ceramic sealing
3.Stone and other materials such as glass, metal seam sealing
4.Other uses
Technical data sheet
| Test standard | Test project | Unit | value |
| Before curing——25℃，50%R.H. | |||
| ASTM C 679 | Flow, sagging or vertical flow | mm | 0 |
| VOC | g/L | ＜80 | |
| GB13477 | surface drying time（25℃，50%R.H.） | min | 30 |
| Curing time（25℃，50%R.H.） | Day | 7-14 | |
| Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.21 days after curing——25℃，50%R.H. | |||
| GB13477 | Durometer Hardness | Shore A | 30 |
| GB13477 | The ultimate tensile strength | Mpa | 0.7 |
| Temperature stability | ℃ | -50~+150 | |
| GB13477 | Movement capability | % | 25 |
| ASTM C 1248 | Pollution / oil, natural stone | No | |
Certification
25HM GB/T 23261-2009；ASTM C920-2011
Color
Black，White，Gray
Package
300ml in cartridge * 24 per box, 590ml in sausage *20 per box
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
Over time I’ve been noticing small cracks appearing on my Keystone Cougar fifth wheel trailers plastic fenders. The cracking is taking place around the screws holding the fenders to the trailer sidewall. It started off with one or two but is slowly progressing to more and more every year. If this kept up and left unchecked, I fear one day I’d lose a fender during travel.
So, I decided this summer to pull the fenders off and see what could be done to beef them up, stop the cracking and prevent a full on failure. A reader recently contacted me via email with some insight to the problem. He believes the cracking might be caused by the indented area for the screws not being flush with the backside.
Ray,
At the end of your shelf repair video, you showed a shot of the cracks around the mounting screws for the fenders.
I just removed the fenders from my trailer so I could caulk the steel wheel tubs to the side of the trailer.
Upon reinstallation of the plastic fenders, I noticed that the indents for the screws are not flush with the back side.
If you over tighten the screws it is going to crack the plastic.
There is room enough to put a washer between the fender and the sidewall.
You might be able to epoxy a washer on the back side to reinforce the plastic.
I enjoy your videos.
Arthur
I elected to take Arthur’s advice and use some washers on the back side of the fender behind the screw holes. Instead of using epoxy I chose to use SikaFlex 291 sealant. I embedded the washer into the Sikaflex and then applied a healthy layer of it all around the indented plastic area. On the front side of the fender behind each screw, I added a small rubber grommet.
Time will tell but I believe the repair and modifications made should help extend the life of my fenders and at least prevent a catastrophic failure at speed on a highway. If not, thanks to thunderbird97 on YouTube for pointing me to a website to order up a replacement set.
“thunderbird97 - Ray here is a website I ordered my fender skirts in case you need it, https://www.icondirect.com , the only difference was old ones were thicker, new ones are made out of better material, holes matched up perfect. Here is the Canada site www.icondirect.ca”
———————————–
Follow our RVing adventures at https://www.loveyourrv.com and https://rvhappyhour.com
Connect with Love Your RV!
Pinterest ► https://www.pinterest.com/loveyourrv
Google+ ► https://plus.google.com/+LoveYourRVonGPLUS
Facebook ► https://www.facebook.com/LoveYourRV
Twitter ► https://twitter.com/loveyourrv
Blog Feed ► https://feeds.feedburner.com/LoveYourRV
Monthly Newsletter ► https://www.loveyourrv.com/mailing-list-sign-up/
Don’t forget to Subscribe! ► https://www.youtube.com/subscription_center?add_user=LoveYourRV
Buy them here https://funwineaccessories.com
We all have that clumsy friend who is always breaking your wine glasses. This Ultimate Party Cup is the perfect solution! Bring them camping, to the beach, in the pool, to the tail gate, or anywhere you go! They are dishwasher safe, microwavable, oven safe, freezer safe, soft, and eco-friendly
Buy them here https://funwineaccessories.com
