18 Years Factory offer Siway SV-602 Epoxy Structural Adhesive A/B for Vietnam Importers
Short Description:
Description SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion. Key Features 1. Room temperature curing Epoxy adhesive 2. Fast cure at room temperature,...
We depend on sturdy technical force and continually create sophisticated technologies to meet the demand of 18 Years Factory offer Siway SV-602 Epoxy Structural Adhesive A/B for Vietnam Importers, We are sincere and open. We look forward to your visit and establishing trustworthy and long-term standing relationship.
Description
SV-602 is a 2-part structural epoxy adhesive developed for such application as dry fixing cladding. It has strong adhesion to metals, woods, reinforced plastics stone, ceramic and masonry. It is the best choice for bonding parts which must withstand weather, moisture and temperature fluctuations. SV-602 will adhere with minimum surface preparation and has a low coefficient of expansion.
Key Features
1. Room temperature curing Epoxy adhesive
2. Fast cure at room temperature, <40 min for reaching a tack-free status under standard environment (STD: 23℃, 50% humidity)
3. Mix ratio of 1:1 by volume or by weight
4. Good mechanical property
5. Bonds a wide variety of building materials
6. Good waterproofing and chemical resistance
Basic Application
1, the external walls of stone material, ceramic and other hang bond;
2, concrete, ceramics, stone, wood and other prefabricated split, bonding and jointing;
3, concrete, stone and so on crack repair;
4, the structure of the localization, anchor, reinforcement and reinforcement.
Technical data sheet
The following data is for reference only and is not recommended for the specification
| Shear strength | Stainless steel-stainless steel/Standard conditions | ≥18 | JC887-2001 | ||
| Pressure shear strength | Stone-stone/ Standard conditions | ≥12 | |||
| Stone-stone/ The freeze-thaw cycle 50 times | ≥10 | ||||
| Stone – stainless steel/ Standard conditions | ≥12 | ||||
| Standard conditions：Temperature=23℃，relative humidity=50%，48 hours curing | |||||
| attribute | SV-602-A | SV-602-B | SV-602(After mixing) | ||
| Colour | gray | white | grey | ||
| Density(g/cm³) | 1.8 | 1.8 | 1.8 | ||
| Viscosity（PaS） | 200-400 | 150-250 | |||
| Effective operating time(23℃) | N/A | N/A | 20min | ||
Certification
JC 887-2001
Color
Part A-Grey Paste/Part B-White Paste
Package
9kg/9kg per unit and 15kg/15kg per unit
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
Reactive Resins produce & sell a wide variety of epoxy resin products for a range of uses including flooring, industrial & marine but also a whole host more.
We produce a range of products that are held in stock or can be quickly made. We can also produce custom formulas for products that solve otherwise insurmountable problems.
Easy Deck faring compound is easy to sand because it is composed of low density glass macro-spheres of various sizes.
https://www.resinstore.com/
CONSEAL P is a unique two-pack, low solvent epoxy primer sealer that can be applied to concrete immediately after it has been laid. CONSEAL P has a unique formulation that gives it the ability to mix with fresh wet concrete while still being resistant to diffusion of water through the uncured coating. CONSEAL P can also be applied to old cured concrete that is free from oil, grease and other contamination.
Can be applied to fresh wet concrete.
Saves money by eliminating surface preparation of new concrete.
Promotes full cure in hot conditions by eliminating water loss.
Reacts with uncured concrete and permanently bonds to it.
Prevents dusting of the concrete surface caused by drying out.
Excellent adhesion to fresh uncured or dry old concrete.
Quick cure allows fast over-coating and finishing of floors.
Allows moisture sensitive polyurethane coatings to be applied within 24 hours of pouring.
Provides superior adhesion for finishing systems.
Easy to use and fast to apply.
Safe non-toxic formulation.
CONSEAL TSF is a two part, totally solvent free, ceramic filled epoxy floor coating. It has exceptional wear and abrasion resistance and is suitable for use in high wear areas and in situations where the use of solvent containing paints may be a problem.
Extremely hard wearing ceramic filled epoxy
Virtually odour free
Easy to apply, lower viscosity than other solvent free epoxy coatings
Tremendous adhesion, even to poorly prepared substrates
Long lasting, eliminates frequent re-coating – saving you time and money
CONSEAL TSF contains an advanced epoxy resin formula
that has considerably lower viscosity than other solvent free epoxy coatings. This attribute renders the product easier to apply and extends the application season into colder weather.
CONSEAL TSF contains a large amount of microscopic ceramic micro-spheres which impart tremendous abrasion resistance to the cured coating. It has excellent opacity and covering power, is resistant to oil, petrol, diesel fuel, most chemicals and has good resistance to sunlight.
CONSEAL TSF is very easy to mix and apply and little skill is required to produce a good job, provided the mixing and application instructions are followed. It can be applied in one thick coat but the inexperienced applicator will achieve a more uniform finish by applying two thinner coats.
CONSEAL coatings are manufactured from the best quality raw materials. They are the result of considerable development work that has produced products of the highest durability, that are easy to apply and are unaffected by cold and damp during application. They can be applied in conditions that would prevent the successful application of many other coatings.
CONSEAL coatings cure to produce a semi- gloss to gloss finish that is sufficiently slip resistant for most dry situations. For wet areas or where maximum slip resistance is required, we have a selection of non-slip additives that can be added to the coating to produce a variety of textures.
APPLICATION Please refer to the detailed application instructions before using this product.
Yeah, we all know Aluminum is spelled “Aluminium” in the United Kingdom! lol. So check out this aluminum framed 1996 Ford E-350 Damon Ultrasport 30 foot motor home we have here!
A great deal at $9000 Canadian dollars (or $6600 U.S. dollars) considering especially as it was purchased 3 years ago!
There are amazing deals out there folks if you look for them!
This baby is the EXACT weight of my nearly 23 foot 2008 Adventurer wood framed Class C RV!!
Stevio takes us on another tour of this very clean and well kept recreational vehicle.
There are lots of great used RV deals for Americans who come up to Canada with their strong American Dollars right now!
My special thanks to “Ten Bar” for allowing us to video his rig!
Keep your wheels on the ground folks!
