17 Years Factory High performance mildew silicone sealant for Kuwait Manufacturer

Gaining customer satisfaction is our company's aim forever. We will make great efforts to develop new and top-quality products, meet your special requirements and provide you with pre-sale, on-sale and after-sale services for 17 Years Factory High performance mildew silicone sealant for Kuwait Manufacturer, We welcome customers, business associations and friends from all parts of the world to contact us and seek cooperation for mutual benefits.

Description

Siway high-performance mildew silicone sealant is a one-component, neutral curing, designed for decoration in the need to provide good anti-mildew performance of the occasion designed by environmental protection products. This product can be easily extruded under wide temperature conditions, relying on moisture in the air to cure into excellent, durable elastic silicone rubber, and most of the building materials in the case without primer can produce superior Of the bondability. It has the following product features:

- easy to operate, you can always use out;

- Neutral curing, suitable for most building materials without adverse effects or corrosion;

- Excellent adhesion: no primer, with most of the building materials to form a strong cohesive force;

- excellent weather resistance and aging performance;

- excellent long-term anti-mildew ability;

- Good environmental performance.

Where  to use

Siway neutral high-performance anti-mildew silicone sealant can be widely used in a variety of high-humidity environment, the interface of the waterproof seal and filling and so on, such as cabinets, basin, toilet, shower, etc., and other needs long-term Moldy effect of the decoration of the occasion.

Key Features

1. 100% silicone

2. Easy to use

3. Waterproofing and weatherproofing

4. Primerless adhesion to most building materials

5. 12.5% movement capability

Technical data sheet

Certification

JC/T881-2001

Color

Black，White，Gray

Package

300ml in cartridge * 24 per box, 590ml in sausage *20 per box

Shelf life

12 months

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

I’m making this video so many people could see that they don’t have to get rid of their old little dinghy unless they really want to if you put a lot of effort a lot of love and a lot of cleaning you can get any little dinghy back 2 operating status. I clean and restore them in Miami for 20.00 per foot. 7864479019 Dont forget to watch Part 2 for the amazing end results! Like and Subscribe!

-~-~~-~~~-~~-~-
Please watch: “Rib Fishing Biscayne Bay”

Alfred Said, “Watch this video”
-~-~~-~~~-~~-~-

Saturday I had a friend come over to help out and we finished mouse and bug proofing the tiny house floor. This floor is now wind and water proof as well.

After installing the aluminum flashing the other day, it sill had some seams and areas where mice or moisture could possibly get in. I want a fully sealed floor to prevent any mice or insects getting into my tiny house.

I got some aluminum flashing tape with tar on one side. This stuff is perfect to seal the seams between the sheets of aluminum flashing. It comes in rolls of 4 inches or 9 inches wide by 33 feet long. I had to cut it into strips to make it go farther.

Eventually I found the best way to cut this stuff is to unroll it and cut it with a utility knife. As I cut a bit, I rolled the cut ends back up until I went through the whole roll of tape.

I then had four rolls of tar flashing tape. This is enough to cover all the seams in my tiny house floor.

To use this stuff simply place it over a seam and press the end to hold it down. Peel the paper backing a little ways and slowly line up the tape over the seam you want to seal. Then run your hand along the tape, pressing it down. Keep going until you have the whole seam covered.

Next, for best results, I press and work the tar into the seams and onto the flashing so it seals very well. I concentrate especially on the edges of the tape so no water or insects ever get in.

We covered both halves of my tiny home floor with the sealing tar tape.

Next I ran along the ends of the floor joists with a drill and put three holes in each board end. Chris followed up and put screws into the holes. This allows the screws to go into the wood without cracking the wood.

I got a rubber mallet at the dollar store which I used to hammer the aluminum flashing down over the ends of the floor framing. Chris followed with a hammer and nails and pounded the flashing into place.

Then we taped off those seams as well. The entire floor frame will be insect proof and mouse proof.

I kept the original plastic sheet that was under the old camper floor. This was a water and bug barrier on the old camper. For my new tiny house this will be a protective layer between the aluminum flashing and the steel frame of the trailer to prevent corrosion between the two metals.

I nailed that into place to secure it. This will also help support the insulation which will be laid in from above after we turn the floor over.

I am very excited about my mouse proof and insect proof floor for my new tiny house on wheels.

Follow my daily progress on the path to self sufficiency on my off grid solar homestead.

https://www.youtube.com/user/techman2015/playlists?view=50&shelf_id=10&sort=dd

Please donate to help keep The Off Grid Project going: https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=3TQSWXLLRZ6HW

Join The Off Grid Project and The Do It Yourself World forum and share your ideas, tips and projects.

https://www.thediyworld.com/forum

The Off Grid Project is presented by The Do It Yourself World.

https://www.TheDIYworld.com

Experiments and projects in off grid living, alternate energy, survival, hiking and more.