16 Years Factory SV-8800 Silicone Sealant for Insulating Glass for Auckland Factory

"Sincerity, Innovation, Rigorousness, and Efficiency" is the persistent conception of our company for the long-term to develop together with customers for mutual reciprocity and mutual benefit for 16 Years Factory SV-8800 Silicone Sealant for Insulating Glass for Auckland Factory, We hope to establish more business relationships with customers all over the world.

Description

SV-8800 is two components, high modulus; neutral curing silicone sealant specifically developed for assembly of high performance insulated glass units as secondary sealing material.

Where to use

It is a two-component silicone that offers variable work life with high bonding strength to maintain the integrity of insulating glass unit, suits both commercial and residential IGU.

Key Features

1. High Modulus

2. UV resistance

3. Low vapor and gas transmission

4. Primerless adhesion to coated glass

5. 100% compatible to SV-8890

Technical data sheet

Certification

GB-24266-2009;

Color

Component A(Base) – White, Component B(Catalyst)- Black

Package

1. Component A(Base): (190L), Component B(Catalyst) (18.5L)

2. Component A(Base):24.5kg (18L), Component B(Catalyst): 1.9kg (1.8L)

Shelf life

12 months

Note

If you want the TDS or MSDS or other details, please contact with our sales person.

A simple and very cheap way to make custom shaped moulds for creating simple resin castings with or without an LED embedded into them.
The mould is based on a popular technique on the Internet which uses common household materials to make good silicone rubber moulds. It’s basically just standard sealant silicone mixed with cornflour (cornstarch) to make a malleable putty into which your master shape is pressed. If using non plastic masters then apply some oil or Vaseline to the object so that the silicone doesn’t stick to it.
When the mould has cured in an hour or so (but leave overnight if possible) then the master can be removed and the flexible mould can then be used to produce replicas from various resins. I like the simplicity of the two part syringe resins which can be bought at dollar store type shops.
To embed an LED I prefer to use the shorter “strawhat” 4.8mm LEDs as it helps to keep the chip as far back from the front of the casting as possible for good light distribution. Bend the leads to the side at right angles to the LED so that it can be placed across the top of the mould with the LED submerged in the resin.

Over time I’ve been noticing small cracks appearing on my Keystone Cougar fifth wheel trailers plastic fenders. The cracking is taking place around the screws holding the fenders to the trailer sidewall. It started off with one or two but is slowly progressing to more and more every year. If this kept up and left unchecked, I fear one day I’d lose a fender during travel.

So, I decided this summer to pull the fenders off and see what could be done to beef them up, stop the cracking and prevent a full on failure. A reader recently contacted me via email with some insight to the problem. He believes the cracking might be caused by the indented area for the screws not being flush with the backside. 

Ray,
At the end of your shelf repair video, you showed a shot of the cracks around the mounting screws for the fenders.
I just removed the fenders from my trailer so I could caulk the steel wheel tubs to the side of the trailer.
Upon reinstallation of the plastic fenders, I noticed that the indents for the screws are not flush with the back side.
If you over tighten the screws it is going to crack the plastic.
There is room enough to put a washer between the fender and the sidewall.
You might be able to epoxy a washer on the back side to reinforce the plastic.
I enjoy your videos.
Arthur

I elected to take Arthur’s advice and use some washers on the back side of the fender behind the screw holes. Instead of using epoxy I chose to use SikaFlex 291 sealant. I embedded the washer into the Sikaflex and then applied a healthy layer of it all around the indented plastic area. On the front side of the fender behind each screw, I added a small rubber grommet.

Time will tell but I believe the repair and modifications made should help extend the life of my fenders and at least prevent a catastrophic failure at speed on a highway. If not, thanks to thunderbird97 on YouTube for pointing me to a website to order up a replacement set.

“thunderbird97 - Ray here is a website I ordered my fender skirts in case you need it, https://www.icondirect.com , the only difference was old ones were thicker, new ones are made out of better material, holes matched up perfect.  Here is the Canada site www.icondirect.ca”

———————————–
Follow our RVing adventures at https://www.loveyourrv.com and https://rvhappyhour.com

Connect with Love Your RV!

Pinterest ► https://www.pinterest.com/loveyourrv
Google+ ► https://plus.google.com/+LoveYourRVonGPLUS
Facebook ► https://www.facebook.com/LoveYourRV
Twitter ► https://twitter.com/loveyourrv
Blog Feed ► https://feeds.feedburner.com/LoveYourRV
Monthly Newsletter ► https://www.loveyourrv.com/mailing-list-sign-up/

Don’t forget to Subscribe! ► https://www.youtube.com/subscription_center?add_user=LoveYourRV