15 Years Manufacturer SV-777 silicone sealant for stone to Oman Factories
Short Description:
Description SV-777 silicone sealant for stone, is an elastomer sealant in modulus, single. Waterproof joints need to be sensitive to natural stone, glass and metal building clean appearance panel for sealing design, it to the moisture in the air after curing in contact, the formation of elastic rubber sealing performance, durability, weather resistance, good combination with most building materials. Key Features 1. 100% silicone 2. Minimized fluid migration 3. Low dirt pick up 4. Water &...
We believe that long term partnership is a result of high quality, value added service, rich experience and personal contact for 15 Years Manufacturer SV-777 silicone sealant for stone to Oman Factories, Any requires from you will be paid with our best attention!
Description
SV-777 silicone sealant for stone, is an elastomer sealant in modulus, single. Waterproof joints need to be sensitive to natural stone, glass and metal building clean appearance panel for sealing design, it to the moisture in the air after curing in contact, the formation of elastic rubber sealing performance, durability, weather resistance, good combination with most building materials.
Key Features
1. 100% silicone
2. Minimized fluid migration
3. Low dirt pick up
4. Water & weatherproof
5. Primerless adhesion to most building materials
6. 25% movement capability
Basic Application
1.Stone curtain wall sealing
2.Engineering ceramic sealing
3.Stone and other materials such as glass, metal seam sealing
4.Other uses
Technical data sheet
| Test standard | Test project | Unit | value |
| Before curing——25℃，50%R.H. | |||
| ASTM C 679 | Flow, sagging or vertical flow | mm | 0 |
| VOC | g/L | ＜80 | |
| GB13477 | surface drying time（25℃，50%R.H.） | min | 30 |
| Curing time（25℃，50%R.H.） | Day | 7-14 | |
| Sealant curing speed and operating time will have different with different temperatures and temperature, high temperature and high humidity can make sealant curing speed faster, rather low temperature and low humidity are slower.21 days after curing——25℃，50%R.H. | |||
| GB13477 | Durometer Hardness | Shore A | 30 |
| GB13477 | The ultimate tensile strength | Mpa | 0.7 |
| Temperature stability | ℃ | -50~+150 | |
| GB13477 | Movement capability | % | 25 |
| ASTM C 1248 | Pollution / oil, natural stone | No | |
Certification
25HM GB/T 23261-2009；ASTM C920-2011
Color
Black，White，Gray
Package
300ml in cartridge * 24 per box, 590ml in sausage *20 per box
Shelf life
12 months
Note
If you want the TDS or MSDS or other details, please contact with our sales person.
Hard case foam liners just don’t hold up very long without reinforcement. Plasti-Dip synthetic rubber protective coating spray is the simple solution to this problem.
Take a peek at a few foam gun container projects including a waterproof Pelican case for a 26.5mm Heckler and Koch flare gun.
Video link showing the boat the flare kit was used on:
Trim-Lok’s extensive selection of trims and trim seals are now available with pre-applied Butyl adhesive sealant or Hot Melt adhesive! Trim-Lok also offers Cyanoacrylate adhesive for application at the time installation.
Visit us online at www.trimlok.com
Secondary Operations & Additional Services Provided:
• Pressure Sensitive Adhesive (PSA) Tape Overlays
• Pre-Applied Hot Melt & Butyl Sealant
• Single Material and Co-Extrusion
• Mitered Corners
• High Tolerance Splicing
• Film Splicing
• Molded Joints
• Plastic Welding
• Slip Coating
• Drilling & Punching
• Inline Printing
• Continuous or Cut to Length
• Notching
• Decorative Mylar Application
• Frame & O-Ring Fabrication
• Cutting
• Mitered Corners
• Hot or Cold Bonded Corners
• Injection Molded Corners
• Custom Color Matching
• Custom Color Compounds Available Upon Request.
• Special Packaging & Custom Kit Assemblies
• Private Label Packaging
Rubber Materials:
• EPDM (Ethylene Propylene Diene Monomer) Sponge & Dense in various durometers
• NBR/PVC (Acrylonitrile Butadiene, Nitrile PVC)
• CR (Chloroprene, Neoprene)
• SI (Silicone)
Plastic Materials:
• TPE (Thermoplastic Elastomer)
• TPO (Thermoplastic Polyolefin)
• TPU (Thermoplastic Polyurethane)
• TPV (Thermoplastic Vulcanizates)
• TPR (Thermoplastic Rubber)
• PVC (Polyvinyl Chloride) Flexible and Rigid
• Flame Resistant PVC
• HDPE (High-density polyethylene)
• LDPE (Low Density Polyethylene)
• LLDPE (Linear Low Density Polyethylene)
• ABS (Acrylonitrile Butadiene Styrene)
• Polypropylene
Markets Served:
• Marine
• Truck & Automotive
• Heavy Equipment
• Recreational Vehicles (RV’s)
• Mass Transit & Rail
• Aerospace & Aircraft
• Agricultural
• Electrical
• Medical Equipment
• Lighting
• Solar Energy
• Water & Wastes
• Toys/Playground Equipment
• Construction
• Fitness Equipment & Sporting Goods
• Furniture
• Appliance
• And MANY MORE!
Extrusion Product Form:
• Simple and Complex Profiles & Shapes
• Tubing, Cord and Rod
• Hollow and Solid
Visit www.TRIMLOK.com for more information!
